Hammock Retreat

Hammock Retreat

This has to be one of my absolute most favorite additions to the backyard. As usual, I was "Pinteresting" (not yet a verb, but will be... just like Google) to find ideas. Anyway, I love to backpack and do all things outdoor, but why leave my hammock all balled up in between backpacking trips when I have a perfectly "hammockable" yard out back? 

With exactly 1 tree in the backyard, however, I had to come up with an idea to hang the hammock, while adding to the aesthetics of the backyard. I wanted a permanent structure (vs. a relatively inexpensive and less eye catching portable alternative). So... with the help of Pinterest and some creative ideas of my own, a project was born.

Here is the backyard before:

Materials I decided I needed:

2- 12ft. 6x6 pressure treated posts

2- 10ft 2 x 10 pressure treated boards

2 bags of sakrete

8, 1/2" x 10 inch bolts with nuts

2, 8 inch eye bolts with nuts

6, 4 in lag screws

Instructions:

Cut off 2 feet from the 6x6 posts and save for later in the project

Dig holes 2 feet in ground double the size of the post

Insert posts into ground, use a level to ensure that it is level on all sides and secure using temporary braces as shown in picture. (I used old 4 x 4 posts from a previous raised garden)

Pour concrete in hole and fill with water

Wait for concrete to set (we waited 48 hrs to make sure it was completely dried through)

I cut off a corner of the "cross beams" to give it a decorative look. I clamped the cross beams together in place and drilled through them using a 1/2in x 12 in long drill bit and an electric drill. This was NOT easy... The 2 foot section you cut off the original posts will now be trimmed with 45 degree angles on each end and attached using lag screws into the upper corners of the structure. (picture below) It's meant to be decorative rather than structural, so just make sure it's secure and you're good to go.

With everything bolted in, it's now ready to install the hammock hangers (eye bolts).

Install the eye bolts evenly on each side. I think I installed the hammock at a height that allowed me to sit on the hammock and swing but also lay in it at a reasonable distance off the ground. For decoration, I laid large stones (about 6$ each) to get to the hammock and mulch and plants all around. The hostas were transplanted from another area, which is why they look as though they are dying- they're in a little shock. 

We laid sod down a little later in the summer and the backyard has come such a long way. It's now one of my absolute most favorite places to lounge around on a weekend day! 

Patio Bar (aka Murphy Bar)

I love company. I love entertaining. I love cooking for large groups of people. I HATE having to go back in the house 5 million times to bring stuff outside. I also hate table clutter. I'll build a bar! Problem solved

When I got the FINAL idea in my head about what it would look like, I dragged myself out of my hammock and to Home Depot I went! I will try to be as detailed as possible, so you can recreate this because, quite honestly, it's PERFECT!

Materials Needed:

2- 8ft sections of Pine Select 1 x 6

1- 2' x 4' hardwood plywood

1- 3 ft section of Pine Select 1 x 2

# 3 chain, 5 ft in length (this will leave a little extra to cut off- each side needs about 2 ft.)

2 long hinges (piano hinge, but mine isn't that long)

Exterior screws

Eye hook with latch

"s" hooks and eye hooks (for chain)

decorative knob

paint and/or stain

heavy duty picture hangers

I used pocket holes to secure the corners

Measurements:

Box measures 36" x 21" (height include the back of the shelf on top)

Suggestions: Build the box first. Then lay the plywood on top and cut out for the perfect fit. Test and retest the hinge to make sure you are installing everything correctly and that everything closes. To attach to the house, I installed a "bracket", drilled into the studs through the hardiplank. I then mounted the box using the heavy duty picture hangers right to the bracket.

Unfinished (obviously)

To give it this "distressed" look, I used a dark walnut stain over the whole box. By the time I was done putting a coat of stain on the whole thing, I immediately began to paint over it with the color (in this case, it was a sage green "craft paint"). When you brush it on, some of the stain mixes with the color and may darken the color slightly. It also pokes through the paint giving it a very old and rustic feel. Remember: You can hardly mess up what's intended to look like it's messed up. So have fun with it and don't think too much about it.

I researched some "outdoor signs" on Pinterest to get an idea of what I wanted to put on the outside. I have tons of different sized/ style stencil letters, so I went with this look. 

For the inside, I wanted a vibrant color that 'popped' When the bar is stocked, the red background helps to contrast the contents and is really much more fun than just a dark stain interior.

This picture allows you to see just how compact it is as contrasted to the whole patio setup. It turned out better than I had expected. It got a clear coat of polyurethane to protect it from the elements and it just happened to shine it up a bit too! Bonus! 

I also installed a hook for a wine cork to hang on the inside as well. 

Stairway to... the 2nd Floor

Final touch to the new staircase and foyer. (Aside from decorating). We have wainscoting in our dining room and I always thought it looked so nice, but also very expensive. So I took to my good and trusty friend Pinterest to help me figure out what to do about wainscoting in my foyer.

For about $120, some serious patience, and a little bit of a creative mind, this is the result.

Chalk out your line. This was about 53" off the baseboard. It got tricky when going off the landing at the top of the stairs but we figured it out. 

My wood choice was the basic 1x4 Whitewood. Since I knew it would be painted, it was the economical option. 

You will need to caulk all the joints. Very important step to making this look like a flawless,  professional job. 

Oh and the wood was glued and nailed to the wall. Wherever possible, I used studs, but this is why the glue comes in really handy. 

Add the 1x2 chair rail along the top. Glue and nail in place. Caulk the joints. For the paint, I used the same color as my trim work. Obviously, this helps to make it appear as if it's always been like that. 

Add your "flare". Boom! 

What do you think?! 

Particle-wha?!?! Particle-where?!?!

"Particle board?!?! You can't cover Particle Board!!!"

They said it couldn't be done. They said I was "crazy". But, I attempted the impossible anyway!!! Just look at those ugly stairs. And right next to the beautiful new banister... 

It was definitely a shot in the dark. I didn't really know what I was doing, but I knew my fall back plan could be to just re-carpet the stairs until a better option was available.

Step 1: Remove all tacks and sand legitimate rough spots. Then smooth over a thin layer of wood filler and wait for it to dry.

Step 2: Sand down the step

Step 3: I used a product called DeckOver from Behr- a very thick paint used to restore old decking and concrete surfaces. This product will fill gaps up to 1/4" deep. With 2 solid coats, the stair tread was sufficiently covered and had a nice finish. 

I did use 3 coats of a clear coat as well to gloss it up a bit!

Step 4: Now that all the stairs are covered, I used a beadboard panel (20$ Home Depot) to cover all 13 risers. With a little Gorilla glue and a few brad nails, the finished look was amazing!

 

The finished product is amazing. You will need to fill the brad nail hole and cover any gaps as necessary (I'm not a perfect cutter). Once I paint the banister, install beadboard and some pops of color, my otherwise drab foyer will be a marvelous entryway for me, my family, and guests to enjoy! 

Hardly your average DIY

So, as my husband sits in the living room, watching football, I chopped away at the house...

I should probably back up a bit. I came home on Friday afternoon after an average work week. I don't know why or how, but I got it in my head that I no longer wanted the carpet on the stairs or the enclosed banister in my foyer. And, usually, when I want something to happen, it happens. So... by the time my husband got home that evening all of the trim had been removed from the banister. And he said nothing. That's typical of him, however, he usually lets me do exactly what I want without comment.

My banister and my foyer area have always been an issue for me. It feels like it closes in on you when you walk in the front door. The banister does nothing but collect dust in all the areas. It's about 3 tones of white / neutral color. It's hideous, to be blunt. I wanted it gone. If you don't believe me, here's a picture to prove what I'm saying.

Once the planning began, there was no going back. And my idea for a grand entryway was about to come true- thanks to the help of my wonderfully talented little brother! 

Time to demo!

 

And the rebuild... 

After you are done gawking at the open banister, gaze over at the stairs... They are particle board and I hate them. But I cannot (structurally and financially) replace the stair treads at this point, so I have a few ideas on how to cover the treads and risers to finish off this amazing addition to our beautiful home. 

Stay tuned for how it all turns out! 

Christmas Candles

What happens when you are begging for gift ideas, strapped for cash, and scrambling for time? Pinterest- that's what happens. I decided to troll my friends Pinterest pages for gift ideas this year and came up with quite a few cool projects to tackle this Christmas.

Cinnamon Stick Christmas Candle

This was a pretty easy project, and the most time consuming part was cutting the cinnamon sticks to the appropriate size. Depending on the candle and whether you use a 50% off coupon at Michael's, the candle could run close to 10$ each. But it's cuteness is worth it.

Gather your supplies. You will need:

A candle (I chose red for this blog, but I also used white ones. FInd them cheap at Ross, TJ Maxx, Marshalls, and Home Goods or use the 50% coupon at Michael's and get them for a steal.)

Bag of cinnamon sticks (also at Michael's, enough in 1 bag to do 1 1/4 candles)

Christmas ribbon

Burlap string

Hot glue gun

Cutting board and serated knife (how I cut the cinnamon sticks)

Steps:

1. Cut the cinnamon sticks to varying lengths, ranging from 3/4 of the way up the candle to about a little 1/2 way up the candle. See picture above. This gives it a staggered look. The best way to cut the sticks without shredding them to pieces is to put the stick on a cutting board and carefully scoring it with the serated knife. Then GENTLY snap the stick in two and repeat with next stick.

2. Once you've cut varying sizes, line them up side by side to visualize what it will look like on the candle. 

3. Begin gluing them onto the candle using the hot glue gun. 

4. Once finished, it should look something like this.

5. Glue the Christmas ribbon on and tie the burlap string around in a bow. DONE! 

I paired it with some Christmas bark for a nice gift to girlfriends. 

Let me know what you think!

Pinterest Much?

So since I got engaged in September, I have been glued to Pinterest, a virtual pinboard of addicting proportions. I recently found a very easy recipe that I tweaked just a little and thought I would share... and then give back to Pinterest.

Pumpkin Cookies/Muffins

Ingredients:
1 box cake mix
1 15oz. can pumpkin
1/3 bag chocolate chips
1/3 bag butterscotch chips



Mix first two ingredients until a pumpkin paste batter forms. Then fold in chocolate and butterscotch chips.


Line muffin pan with baking cups. Pour about 3/4 of the way full.


For cookies, spoon onto a greased cookie sheet (a little Pam non stick spray works fine).



Bake at 350 for 13 minutes (cookies) or 23 minutes (muffins). The end result is an incredibly moist and fluffy muffin/cookie.



Enjoy... but share!

Simple enough?